10 Things We Hate About Suzuki Jimny Replacement Key

10 Things We Hate About Suzuki Jimny Replacement Key

Suzuki Motorcycle Key Replacement

When you need to replace your Suzuki motorcycle key, you'll need to make sure that your locksmith is knowledgeable about this type of job. This is because traditional motorbike keys can be hard to work with.

Before they cut a key, the majority of locksmiths require proof of ownership. This could be your registration or bill of sale or photo ID.

Ignition Cylinder Replacement

The ignition cylinder is the primary element that binds everything. The ignition cylinder is a rectangular silver-shafted device into which you place the key. The cylinder has an electrical attachment that connects to relay switches that supply power to various motorcycle systems. If the cylinder is not functioning properly, you might find that your vehicle is not starting or that the key isn't turning in the switch.

If you have a conventional motorcycle key with a steel blade, you can simply obtain an additional one cut by your local locksmith.  suzuki wagon r replacement key  can make a duplicate key using the code from your existing one.

In cases where the key isn't turning on the switch or if it snaps inside the lock, you will require replacing your ignition cylinder. This is more complicated and requires a professional to deal with. Making a call to a local locksmith to make a new Suzuki bike key on-site is the most reliable option.


To replace the cylinder, you must first remove and clean the old one. Then, you'll need to locate a diagram of the key on paper or template that lists all the tumblers on the cylinder. Once you've completed this, you can take out each tumbler, and place it in the appropriate location on your paper key diagram.

Ignition Switch Replacement

Ignition switches become stuck due to various reasons, the most common being from the use of wet oil lubricants like WD-40. While these can repair the switch at the moment, they can be detrimental in the long run as they attract dirt, which can eventually jam the switch and cause further issues when starting your motorcycle. Instead of using lubricants that are wet, you can use dry graphite. Hold the pencil's tip over the opening of the ignition switch and gently rub the graphite section so that the powdered graphite falls directly into the opening. Continue to do this until you've got a sufficient amount of powdered graphite inside the switch's opening.

The next step will be to take your cylinder code to a locksmith, the majority of them will handle this on their own, however there are a few that cannot. You'll have to look around to find one who can take care of this.

Once you have figured out the cylinder code, you can change the ignition switch, or at a minimum, take off the triple clamp on the top. It's a simple procedure and can be done at home with the tools you already have in your garage. After the ignition switch has been removed from the bike, replace it with a new ignition and reinstall the upper triple clamp. Be sure to use a good quality lock set for your bike.

Ignition Wiring Replacement

If you have lost your motorcycle key or broken it, leaving a small piece of it stuck in the ignition, you'll need to find an alternative solution. There are a variety of ways to get your key replaced, some of which are much more expensive than others. If you have your cylinder's code, then you can take it to a locksmith and have them cut an entirely new key for you. This method may not be applicable for older motorcycles or if the codes for cylinders have been altered.

You can also take the ignition cylinder into the local dealer. They should be able to get you an entirely new key if you have the VIN number, but it will likely cost more than the other alternatives. You can also contact your local locksmith to ask whether they can make motorcycle keys. It is best to call ahead before taking your bike in, because some locksmiths might not have the right tools or knowledge about motorcycle locks.

If you have a spare key is kept in a secure place you can use it to start your motorcycle. Keep this key in a secure place to guard it from theft. It is also recommended to have a spare key made in the event you lose your primary one or it gets damaged.

Keyless Entry System Replacement

Motorcycles are fun and provide plenty of freedom. However, they're susceptible to the same issues as cars and trucks. If you lose your motorcycle keys or a part of the key is damaged in the ignition, you will need to contact locksmiths who have experience dealing with motorcycle keys. They can assist you to get back on the road as fast as is possible.

The best method to avoid losing your motorcycle keys is to keep a second one in the car. Put the key in a location that is secure from being moved or disturbed. It could be in an apron, a basket or even a drawer that you rarely use. It is important to teach your children and family members to treat this space with respect.

You can also get the spare key in your dealer or bike shop. These are usually more expensive than a locksmith but they will be able to make the key you require. They will need the code from your ignition cylinder. The code is located on the silver shaft where you put your key.

Most locksmiths can make keys for your Suzuki motorcycle. However the process is slightly different from that of traditional cars and trucks. Keys for motorcycles are more complex because they have electronic transponder technology that lets them start your vehicle. This makes them more difficult to copy than a standard car or house key.